Before we get into the heart of this presentation, I'll briefly mention that among the acids we can get, 5% white vinegar and citric acid are the best acidifiers for hobbyists because they're safe for home use. Large-scale collections and nurseries use stronger, more concentrated acids due to the large volumes of water required. These acids need very careful handling, so I'll leave that up to the professional growers who know what they're doing.
When I started acidifying my water in early 2012, Darryl Craig (CoronaCactus Nursery) was still active on the forum, and he said "a pH meter is the only way to go". He was spot-on about that, and the results have been speaking for themselves ever since (many thanks wherever you are, Darryl! ). Now, which meter should we select? After doing a fair amount of research, I decided on a Milwaukee Instruments pH 600 pen-style digital meter, available on Amazon here. At $21.95, IMO a great buy for the money since it can be calibrated for accuracy (the other pen-style meters I found didn't have this feature). Here's what you'll get coming out of the box:
The screwdriver's purpose will be obvious once you start using it. The meter also comes with instructions -- not difficult to figure out, but please follow them. (Any negative reviews you see on Amazon were generated by people who clearly weren't paying attention in class! ) An important thing to note in the instructions is that the meter's electrode should not be allowed to stay dry for extended periods of time. I kept my first meter in an open jar with some water, but I had a bad habit of forgetting to refill it before the jar went dry. After enough times of making that mistake, the electrode finally pooped out, so I had to buy another pH 600. If there was a way to cover the jar, evaporation wouldn't be a problem, but what to do? Hmmmmm... There's the answer -- a jar with a plastic lid. In my case, an empty coffee jar:
If you cut the hole to the proper fit, you're all set:
It'll take a verrrrrrry long time before you lose too much water to evaporation, so this arrangement is a wonderful way to keep the electrode wet without having to constantly "babysit" the water level. Here's another important note you'll see in the instructions -- distilled water will ruin the electrode, and it's the ions in plain old tap water that'll keep it going. The initial calibration procedure sets the meter to 7.0 (pH-neutral), but the pH tends to creep up a little when you store it in the water jar. When you buy your pH 600, you'll also need to buy a bottle of 7.0 reference solution (available on Amazon here or at your local hydroponic shop). The reference solution and the screwdriver that came with the meter will allow you to calibrate it back to 7.0 right before you test your acidified water. And that, my friends, is how you get accurate readings. Now I'll give you some of my own instructions on the preparation of acidified water as it is properly tested with a pH meter:
- Fertilizers tend to lower the pH a little, so whenever you fertilize, put your fert into the water first, then start with a small amount of vinegar or citric acid. Sources discussing acidification recommend a fairly wide pH target range of 5.0 - 6.0, so check the meter's reading and continue adding acidifier until you hit your desired target. If it goes below 5.0, you've over-acidified -- dump out the water and begin the process again. Once you determine the right amount of the acidifier you'll use, write it down for future reference.
- The pH of tap water can sometimes fluctuate (usually higher in summer and winter than spring and fall), so it's a good idea to periodically test the pH of your acidified water. Not sure that we need to do this every single time we water our plants, but it should be a standard part of your practice every 2-3 months and/or when you skip on the fert from time to time.
- Although potting media don't have a pH factor when they're dry, they can alter the pH of the water being taken up by the roots of our plants. For those of us OCD-driven growers who don't like to guess about anything, here's an extra step you can take:
A. Fill an empty pot with your mix of choice and drench it through and through.
B. Capture the runoff in a container -- make sure you have plenty.
C. Filter the runoff with a paper coffee filter and funnel.
D. Now that you have clean runoff water, test it with your meter, and you'll get the final pH.
And finally, the pH 600 is a rugged, reliable instrument -- treat it well, and your meter should last a good long time.